AC Shelby Cobra 427
The stuff of legend, this is. Carroll Shelby approached Ford MoCo in order to shoehorn its monster 520 bhp, 427 V-8 into the AC Cobra, a British sports car. The result was magic and threw down with the previously victorious Chevy Corvettes in auto racing. It was a triumph of huge proportions. Shelby’s beast did the quarter-mile in 13.2 seconds and handled like it was on rails. And though the production of these monsters ended in 1967, the automotive world would never be the same
Like many British manufacturers, AC Cars had been using the Bristol straight-6 engine in its small-volume production, including its AC Ace two-seater roadster. This had a hand-built body with a steel tube frame, and aluminium body panels that were made using English wheeling machines. The engine was a pre-World War II design by BMW which by the 1960s was considered dated. Bristol decided in 1961 to cease production of its engine and instead to use Chrysler 313 cu in (5.1 L) V8 engines. AC started using the 2.6 litre Ford Zephyr engine in its cars. In September 1961, American automotive designer Carroll Shelby wrote to AC asking if they would build him a car modified to accept a V8 engine. AC agreed, provided a suitable engine could be found. Shelby went to Chevrolet to see if they would provide him with engines, but not wanting to add competition to the Corvette they said no. However, Ford wanted a car that could compete with the Corvette and they happened to have a brand new engine which could be used in this endeavor: Ford's 260 in³ HiPo (4.2 L) engine – a new lightweight, thin-wall cast small-block V8 tuned for high performance. Ford provided Shelby with two engines. In January 1962 mechanics at AC Cars in Thames Ditton, Surrey fitted the prototype chassis CSX2000 with a 260 ci Ford V8 borrowed from Ford in the UK; the 221 ci was never sent. However, early engineering drawings were titled "AC Ace 3.6". After testing and modification, the engine and transmission were removed and the chassis was air-freighted to Shelby in Los Angeles on 2 February 1962. His team fitted it with an engine and transmission in less than eight hours at Dean Moon's shop in Santa Fe Springs, California, and began road-testing.
Like many British manufacturers, AC Cars had been using the Bristol straight-6 engine in its small-volume production, including its AC Ace two-seater roadster. This had a hand-built body with a steel tube frame, and aluminium body panels that were made using English wheeling machines. The engine was a pre-World War II design by BMW which by the 1960s was considered dated. Bristol decided in 1961 to cease production of its engine and instead to use Chrysler 313 cu in (5.1 L) V8 engines. AC started using the 2.6 litre Ford Zephyr engine in its cars. In September 1961, American automotive designer Carroll Shelby wrote to AC asking if they would build him a car modified to accept a V8 engine. AC agreed, provided a suitable engine could be found. Shelby went to Chevrolet to see if they would provide him with engines, but not wanting to add competition to the Corvette they said no. However, Ford wanted a car that could compete with the Corvette and they happened to have a brand new engine which could be used in this endeavor: Ford's 260 in³ HiPo (4.2 L) engine – a new lightweight, thin-wall cast small-block V8 tuned for high performance. Ford provided Shelby with two engines. In January 1962 mechanics at AC Cars in Thames Ditton, Surrey fitted the prototype chassis CSX2000 with a 260 ci Ford V8 borrowed from Ford in the UK; the 221 ci was never sent. However, early engineering drawings were titled "AC Ace 3.6". After testing and modification, the engine and transmission were removed and the chassis was air-freighted to Shelby in Los Angeles on 2 February 1962. His team fitted it with an engine and transmission in less than eight hours at Dean Moon's shop in Santa Fe Springs, California, and began road-testing.
.JPG)
AC produced only 23 AC Cobra 427 competition roadsters. In 1966, one was selected and converted into a special model called the 427 (CSX3015) "Cobra to End All Cobras." The first one of these was originally part of a European promotional tour before its conversion. This conversion called for making the original racing model street legal with mufflers, a windshield and bumpers amongst other modifications. But some things were not modified, including the racing rear end, brakes and headers. The most notable modification is the addition of Twin Paxton Superchargers, TPS. Shelby crafted two 427 models by himself, adding the TPS to each, and gave them the model number CSX3303. He gave one of the two cars to comedian Bill Cosby, a close friend, and kept the other for himself. Shelby eventually converted his car to make it street-legal, including the addition of windshields and mufflers, and renamed it the 427 SC (Semi-Competition).
When Cosby attempted to drive his CSX3303, he found that it was very difficult to keep under control; he later recounted the experience on his 1968 stand-up comedy album 200 M.P.H.. Cosby gave the car back to Shelby, who then shipped it out to one of his company's dealers in San Francisco, S&C Ford on Van Ness Avenue. S&C Ford then sold it to customer Tony Maxey. Maxey, suffering the same issues as Cosby did with the car, lost control and drove it off a cliff, landing in the Pacific Ocean waters.
Shelby used his CSX3303 as a personal car over the years, sometimes entering it into local races like the Turismos Visitadores Cannonball-Run race in Nevada, where he was "waking [up] whole towns, blowing out windows, throwing belts and catching fire a couple of times, but finishing."[19] The CSX3015 was auctioned on 22 January 2007, at the Barrett-Jackson Collector Car Event in Scottsdale, Arizona, for $5 million plus commission (£2.8 million), a record for a vehicle made in the U.S.
From the late 1980s onwards, Carroll Shelby (Shelby Automobiles, Inc.) and associated companies have built what are known in the hobby as "Continuation Cars"; Shelby authorized continuations of the original AC-built Cobra series. Produced in Las Vegas, Nevada, these cars retain the general style and appearance of their original 1960s ancestors, but are fitted with modern amenities. Initially the car everyone wanted in a Continuation was a 427 S/C model which was represented in the CSX4000 series. This was meant to continue where the last 427 S/C production left off, at approximately serial number CSX3560 in the 1960s.
The initial CSX4000 series cars were completed from the chassis built by McCluskey Ltd as well as other new parts and reconditioned Ford engines. Given the value of the vehicle many "extra" cars have appeared over the years, even some sharing the same chassis number. Gradually as the vintage parts supply ran low, newly constructed frames and body panels were obtained from a variety of suppliers. The production of chassis numbers CSX4001 to CSX4999 took roughly 20 years and many different business relationships to complete.
All models of Cobra produced are available now as continuations. In 2009, CSX4999 was produced, concluding the 4000 series. Production has continued with the CSX6000 serial numbers, featuring "coil over" suspension. The 289 FIA "leaf spring" race version of the car is reproduced as CSX7000, and the original "slab side" leaf spring street car is the CSX8000 series.
To date most continuations are produced in fiberglass, with some ordering cars with aluminium or carbon-fibre bodywork.
In 2004, at the North American International Auto Show in Detroit, Ford unveiled a concept for a modernized AC Cobra. The Ford Shelby Cobra Concept was a continuation of Ford's effort to bring back the retro sports cars that had been successful in the 1960s, including the Ford GT40 and the fifth generation Ford Mustang.
Cars were also produced by AC Cars until 2006, and since 2009 have been produced by AC Heritage, who are licensed by AC to produce 289 and 427 continuations.
In 2014 Shelby American announced a limited edition production of 50 cars for the 50th anniversary of the original 427 Shelby Cobra.
Source:Wikipedia
0 comments